ジークリング リンパック
表面がリナテックス素材の搬送・加工用ベルト
ジークリング リンパック
ジークリング リンパックは以下の用途でご使用いただけます。
- 梱包箱製造でのラべリングや折り目付け工程
- スズのプレート処理と、包装と接着工程
- 重い梱包箱や段ボール製造工程
- 高い摩擦係数での搬送工程
特性
- 高いグリップ力
- 高摩擦係数
- 高い耐摩耗性
Feeder belts / Folder belts
| Antistatic | Total thickness ground3) from/to [mm] | FW-value approx. [N/mm width] | Shore A hardness of the top face | dmin approx. [mm]*3 | Operational temperature allowed [°C] | ||
| RT 6-L | 1) light red | 3-8 | 6 | 38-40 | 30/65 | +10/+70 | |
| R 6-L | 1) light red | yes | 3-8 | 6 | 38-40 | 30/65 | +10/+70 |
| R 10/2-L | 1) light red | yes | 4-8 | 10 | 38-40 | 40/65 | +10/+70 |
| R 10/3-L | 1) light red | yes | 8-15 | 10 | 38-40 | 65/120 | +10/+70 |
| UU 20 U-L | 1) light red | yes | 4-7 | 4) | 38-40 | 30/60 | +10/+70 |
| UU 60 U-L | 1) light red | yes | 8-12 | 4) | 38-40 | 30/100 | +10/+70 |
1) When ordering please indicate the total thickness after the coating letter L or U, e.g. R 10/2 – L 8.
3) Within the total thickness a graduation in one tenth of 1 mm is possible.
4) Depending on the thickness of the coating. Elongation at fitting:
6 % (UU 20 U – L) or 4 % (UU 60 U – L).
* Established in line with ISO 21181:2005
*2 Shaft load at 1 % elongation, measured in N/mm belt width.
*3 The smallest permissible pulley (or roller) diameters depend on the belt thickness and were established at normal ambient conditions. Low temperatures or particularly low humidity require larger diameters.
Folder and carrier belts
| Antistatic | Total thickness non-ground2) from/to [mm] | Effective pull at 1% elongation (k1% relaxed) [N/mm width]* | Shore A hardness of the top face | dmin approx. [mm]*3 | Operational temperature allowed [°C] | |
| T1-L1) light red | yes | 3.5 - 7* | 5) | 38 – 40 | 40/60 | +10/+70 |
| T2-L1) light red | yes | 5.0 - 12.5* | 5) | 38 – 40 | 100 | +10/+70 |
1) When ordering please indicate the total thickness after the coating letter L or U, e.g. R 10/2 – L 8.
2) The following thicknesses are possible in the non-ground version:
T 1 – L = 3.5/4.5/6/7 mm
T 2 – L = 5/6.5/8.5/9.5/10.5/12.5 mm
1) When ordering please indicate the total thickness after the coating letter L or U, e.g. R 10/2 – L 8.
2) The following thicknesses are possible in the non-ground version:
T 1 – L = 3.5/4.5/6/7 mm
T 2 – L = 5/6.5/8.5/9.5/10.5/12.5 mm
3) Within the total thickness a graduation in one tenth of 1 mm is possible.
5) On request
* Established in line with ISO 21181:2005
*3 The smallest permissible pulley (or roller) diameters depend on the belt thickness and were established at normal ambient conditions. Low temperatures or particularly low humidity require larger diameters.
