SelectYourLanguage

Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2

eurocol
026 EUROBLOCK MULTI

026

One-component damp proof coating - DPM. Damp proofing up to 4 CM % (95 % RF) in combination with flooring works. Dispersion based.

026-euroblock-multi.jpg
  • 026-safety data sheet uk.pdf

    026-safety data sheet uk.pdf

  • pdf-product-specification.pdf

    pdf-product-specification.pdf

  • 026 ec1plus_licence uk.pdf

    026 ec1plus_licence uk.pdf

Product Typification

DPM for suppressing residual construction moisture in sand/cement screeds.
Basis : Polyvinylidene chloride.
Colour : Blue.
Consistency : Thin liquid.

Product advantages:
  • Very low emission
  • Easy application
  • Favourable spreading capacity
  • Non-flammable
  • Fast drying 
  • Very low-emission installation material certified according to EMICODE EC1 Plus.
  • Declared by baubook, "ecological building product".

Performances

Consumption : Approx. 50 - 75 g/m², per coat. 
When diluted 1:1 with water), approx. 50 g/m².
Curing : 24 hours.*
Flammability : Non-flammable.
Frost resistance : No.
Special quality : Damp proof membrane up to 4 CM%, 95 % RF.
Specific weight : 1.24 kg/l.

Application

Application:

For suppressing residual construction moisture in sand/cement screeds and power floated concrete:

  • Suitable for all kinds of floor covering when applied in two coats. 
  • Suitable for very impervious floor covering when applied in three coats. First coat 1:1 diluted with water.

Working Process

Tools : Lambswool roller or brush.
Curing : 24 hours.*
Storage : Store cool and free from frost.
Shelf Life : 12 months, in unopened packaging.
Drying : First coat 20 minutes.* Second and third coat 60 minutes.*
Frost-proof : No.
Remarks : 

Technical information and safety data sheets of other laying materials and floorings must be observed!

Not applicable under parquet installations with 1K SMP adhesives. 

Eurocol 026 Euroblock Multi is not a building sealant according to DIN 18195. Ensure sufficient rear ventilation behind cupboards and skirting boards in the closed off floor construction! Not to be used for damp-proofing on composite cement screeds, on concrete, on moisture-sensitive substrates such as calcium sulphate bonded screeds, magnesia screeds, stone wood screeds, on ceramic tiles, stone floors, terrazzo, mastic asphalt screeds.

EMICODE, further information at www.emicode.com.


* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

Consumption:
Approx. 50 - 75 g/m², per coat. 
When diluted 1:1 with water), approx. 50 g/m².

Substrate:
  • 026 Euroblock Multi is suitable for sand/cement screeds, which have a good tensile and compression strength and are free from cracks. The subfloor should also be clean, dry and free from grease and dirt, according to the requirements of BS 8203 or DIN 18 365.
  • Remove possible adhesive residues completely.
  • First blast-track power-floated floors.
  • In advance always seek our technical data sheets. In doubt about the application ask for technical advice.

Note:

During application subfloors may not contain more than 4% of moisture. Do not use 026 Euroblock Multi when the construction of the subfloor is exposed to permanent groundwater pressure.


User manual:
  • First apply a diluted (1:1 with water) coat 026 Euroblock Multi evenly with a lambswool roller and/or brush on the subfloor.
  • When installing linoleum apply after drying (approx. 20 minutes, depending on temperature, relative humidity and subfloor) a second undiluted coat 026 Euroblock Multi at right angles to the first (when installing linoleum).
  • When installing an impervious floor covering apply a third undiluted coat 026 Euroblock Multi, again at right angles to the previous coat.
  • Drying time between the second and third coat is approx. 60 minutes (depending on temperature and relative humidity).
  • Before applying a levelling compound the last coat 026 Euroblock Multi has to dry for at least 12 hours. Apply levelling compound in a minimum layer thickness of 2 mm.
  • Remove any fresh spots immediately with water.

Working conditions:
Required surrounding temperature : 18° - 23 °C.
Material and subfloor temperature : min. 15° - max. 20 ºC.
Relative humidity : 40 - 70%.





Quality and guarantee

Environment and health

GISCODE : D1
LEED : VOC 0 g/l, meets: IEQ Credit 4.1
DGNB : VOC 0 %, quality level: 4
Hazard Class : None.
Safety and environment : Safety data sheets of Forbo Eurocol products according to EEG-guideline 91/155. Keep out of reach of children. Do not eat, drink or smoke while processing the product. Only give completely empty containers for recycling. Material residues can be disposed of as household waste.





Articles

ArticleDefinitionPackagingEAN-code
026Euroblock Multi   12 kg jerry can 8 710345 486026