• Beautiful eggshell finish
• No VOC emission
• Water-based
• Easy to process
• Highly UV-proof
• Highly chemical-proof
• Rubber-proof (e.g. hot car tires)
• Hardly prone to scratching
• Extremely good adhesion
• Neutral smell

• The 307 WallDesign or coloured (390 FloorColouring) leveling floor must be applied in accordance with the steps in the relevant instructions. This layer must be completely dry. The substrate must be clean, permanently dry, and free of grease, dirt, and dust.
• The floors must be pre-treated with a layer of 301 BaseSealer. After the layer of 301 BaseSealer has been applied, the floor can be finished with 311 TopCoat after a drying time of 3 - 4 hours (but no later than within 48 hours). After 48 hours, the 301 BaseSealer layer must first be sanded with K180 sandpaper and then thoroughly vacuumed to remove dust before the 311 TopCoat can be applied. 
• Wear shoe covers on the floor during application to prevent footprints.
• WallDesign walls can be finished directly with 311 TopCoat after drying.

• Add all of the hardener (component B) to the base (component A). Then mechanically mix the components to a homogeneous mass for at least 3 minutes. Next, pour into a clean empty bucket and mix thoroughly once more. The mixer must have a (plastic) coating.
• When applying the product to the floor wear shoe covers to prevent foot prints.
• Apply this coating system in at least 2 layers, using an epoxy roller or 2-component Nylon roller 13 mm. The coating must be applied evenly and without pressure across the entire surface. We advice to then roll out the coat in random directions.
• After the first coat of 311 TopCoat has been applied, allow at least 8 hours to dry, yet apply the second coat of 311 TopCoat within 48 hours at the latest. After 48 hours, the first coat must first be sanded with a a grit 100 or 120 gauze and then vacuum-cleaned to remove
  all dust. Allow a minimum drying time of 24 hours. The above-mentioned drying times apply at a temperature of 20 °C. The lower the temperature, the longer the drying time.
• After at least 7 days the top coat is fully mechanically and chemically resistant. This is why it is important that within these 7 days the floor or wall does not get stained and/or damp, as this may lead to a damaged finishing.
• Fresh product stains (not hardened yet) should always be removed immediately with water. After it has hardened the material can only be removed mechanically.
• Always consult our technical production information sheets first. When in doubt about the use of the product, please contact our Technical Help Desk.
• Clean product traces and dispose of cleaning water according to locally applicable environmental rules, and do not dispose of it in the sewer.
• Avoid eye and skin contact and use suitable personal protection equipment (see the safety sheet for this).

Contains 1.2 benzisothiazole-3(2H)-on, Bis(1,2,2,6,6-pentamethyl-4-piperidyl)sebacat, Methyl-(1,2,2,6,6)-pentamethyl)-4-piperidyl)sebacat. May cause an allergic reaction.

More information:

• Keep out of reach of children.
• Thoroughly ventilate the space during and after the application and drying process.
• Do not eat, drink or smoke while you are working with this product.
• If the product comes into contact with the eyes or skin, wash immediately and thoroughly with water.
• Dispose of product residues and cleaning fluids according to locally applicable environmental rules and not into the sewers.
• For comprehensive information about the safety measures refer to the safety information sheet on our website www.eurocol.nl.
  

Conditions for processing:
Desired room temperature : 10 - 23 °C.
Temperature for material and subfloor : min. 10° – max. 23 °C
Relative humidity : 50 - 80%. (> 60% make sure the room is sufficiently ventilated)