Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2



Fast-setting, cement-based filling and repairing compound, fast setting and firm repair mortar. Can be used up to 50 mm layer thickness.

alt-de_940_europlan quick.jpg
  • safety data sheet_eurocol_940_europlan_quick_uk.pdf

    safety data sheet_eurocol_940_europlan_quick_uk.pdf

  • licence_940-quick_blue angel_2021_uk.pdf

    licence_940-quick_blue angel_2021_uk.pdf

  • licence_940-quick_ec1plus_2020_uk.pdf


  • pdf-product-specification.pdf


Product Typification

Fast setting and firm repair mortar.
Basis : Special cements, mineral aggregates, plaster, polymer-bound levelling and defoaming agents, thickeners, additives.
Colour : Grey.
Consistency : Powder.

Product advantages:
  • Stable, very high load-bearing, fast curing and fast walkable, cementitiously repairing compound.
  • For repairing and levelling stairs and landings.
  • For filling screed break-outs, holes and deeper unevenness.
  • For shaping edges, transitions and slopes.
  • For filling and smoothing joints of fully bonded, approved Eurocol decoupling boards (e.g. 823 Eurofloor Reno).
  • Applicable in layer thickness up to 50 mm. On decoupling boards (e.g. 823 Eurofloor Reno) up to 10 mm.
  • Well extendable towards "zero" mm layer thickness.
  • Stable and smooth adjustable by adding water.
  • Stretchable up to 30 % with 846 Europlan Sand for layer thickness over 10 mm.
  • The product can be used on underfloor heating and is suitable for use with chair castors according to DIN EN 12529.
  • For interior use.
  • Very low emission laying material, certified according to EMICODE EC 1 Plus.
  • Declared by baubook, "ecological building product".
  • Blue Angel UZ113.


Bureau Wheelchair resistance : From 1 mm layer thickness.
Classification : CE: DIN EN 13813: CT-C40-F7. A1fl (EN13501-1)
Consumption : Approx. 1.5 kg/m² per mm layer thickness.
Flammability : Non-flammable.
Frost resistance : Yes.
Passableness : Approx. 45 minutes at (18 - 20) °C.*
Special quality : Stable and smoothly adjustable throug happropriate water addition. Over 10 mm layer thickness with up to 30 % quartz sand stretchable. Extendable towards "zero" mm thickness..


  • For levelling and repairing steps and smaller floor areas.
  • For filling cracks, holes etc. in cement-based floors. 

Working Process

Layer thickness : Maximum 50 mm.
Tools : Trowel or putty-knife.
Mixing ratio : Add 25 kg of 940 Europlan Quick to 5,5 - 6 litres of water.
Processing time : Use within 15 minutes after mixing.*
Storage : Store cool and dry.
Shelf Life : Approx 6 months, in unopened packaging.
Drying : App. 45 minutes.
Cleaner : Water.
Frost-proof : Yes.
Remarks : 

Technical information and safety data sheets of other laying materials and floorings/parquet must be observed!

Apply flooring to the filled area within the next few days!
For absorbent subfloors keep a minimum layer thickness of 2 mm, for non-absorbent subfloors a minimum layer thickness of 3 mm.
When used under parquet, a minimum layer thickness of 3 mm must be observed.

In case of multi-layer application, the layer thickness of the second application must not exceed the layer thickness of the first application.

After application of levelling compound.

  • Fresh surfaces should be protected against direct sun light, draughts, high temperature (above +30°C), rain and frost.
  • To obtain the recommended long term technical performance of product, after finishing levelling works installation of floor covering should be done within the shortest period of time, which depends on product’s drying time within 3 to 7 days, otherwise the surface should be protected with a suitable coating or covering.
Not suitable on floating dry screed elements or floating wood-based panels.
The readiness for laying is dependent on the thickness of the layer and depends in particular on the climatic conditions on site.

Wear protective glasses and gloves.
If the adhesive or installation material comes into contact with your eyes, wash out immediately with plenty of water and consult an ophthalmologist.
Protect your hands with waterproof, robust gloves.
Wear long trousers.
Avoid prolonged skin contact with the adhesive or installation material. Thoroughly clean affected skin parts with water immediately.
The longer fresh adhesive or installation material remains on your skin, the greater the risk of serious skin damage.
Keep children away from fresh adhesive or installation material.

EMICODE, for more information visit Wear protective gloves / eye protection.For levelling work in connection with subsequent parquet adhesives using Eurocol 1K or 2K parquet adhesives, only use Eurocol 048 Europrimer Plus or reactive Eurocol primers.

* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

Approx. 1.5 kg/m² per mm layer thickness.

  • 940 Europlan Quick can be applied on any type of stony subfloor that is rigid and has a good tensile and compression strength. The subfloor should also be clean, permanently dry and free from grease and dirt, according to the requirements of BS 8203 or DIN 18 365/DIN 18356.
  • Prime smooth and impervious subfloors such as tile floors, granito, terrazzo, asphalt floors and bituminous substrates as well as old and sandpapered (water-resistant) adhesive residues with 044 Europrimer Multi/044-1 Europrimer Multi Plus/070 Europrimer Fill with a foam roller.
  • Prime porous cement screeds with 044 Europrimer Multi/044-1 Europrimer Multi Plus or 049 Europrimer ABS with a lambswool roller or damp with water.
  • Cracks/seams in the subfloor must be fixed with 021 Euroblock Reno in combination with 063 Eurotape or with 808 Eurojoint Connector possibly in combination with 846 Quartzsand. Alternatively with Europlan 913 Silicate sealing compound.
  • Appropriately dimensioned Eurocol edge strips are to be used for rising building components.
  • In advance always seek our technical data sheets. In doubt about the application ask for technical advice.

User manual:
  • Mix the powder in the specified quantity (see technical data) with clean, cold water using an electric mixer to form a smooth, lump-free mass. For partial quantities use approx. 0.22 - 0.24 litres of water per kg powder. Only so
    mix a lot of powder as can be processed within the working time
  • Depending on the intended use, varying the amount of water can produce a mortar that is stable to smooth and easy to remove.
  • Apply the ready-mix within the working time in as one operation as possible until the desired layer thickness is achieved.
  • Smooth stairs or repair areas with a damp sponge after smoothing. If walkable, used gauges can also be removed.
  • During the setting of the levelling compound, avoid draughts and intense sunlight.
    This can lead to a too fast withdrawal of moisture, which "burns" the filler layer, pulverizes the surface edge zone and shrinkage cracks can occur.
  • When laying on underfloor heating, the heating must be kept in operation for 3 days before, during and up to 7 days after laying with a surface temperature of (18 - 22) °C.
  • In case of multi-layer levelling and levelling works with self-levelling compounds, apply an intermediate coat of completely set first levelling compound before applying the second one and allow to dry.
  • For application thicknesses above 5 mm, stretching with sand (grain size 1 - 3 mm) is possible. When mixing, the stretching material is added as the last component. The maximum amount of additive must not exceed 30 % of the filling compound.

Processing conditions:

at least 15 °C floor temperature,
at least 18°C material and room temperature,
35-75% relative humidity, recommended <65%.

Quality and guarantee

Environment and health

GISCODE : ZP1 Cementitious products, low chromate.
LEED : VOC 0 g/l, meets: IEQ Credit 4.1
DGNB : VOC 0 %, quality level: 4
Hazard Class : Observe notes in the safety data sheet/label!
Safety and environment : Safety data sheets of Forbo Eurocol products according to EEG-guideline 91/155. Wear protective gloves and safety glasses! Keep out of reach of children. Do not eat, drink or smoke while processing the product. Only give completely empty containers for recycling. Material residues can be disposed of as household waste.
MSDS : For extensive information about safety and environment we refer to our website


ArticleDefinitionPackagingShipping unit
940Europlan Quickpaper bag à 25 kg42/pallet