• Dust reduced
• EMICODE EC 1PLUS  (very low emission)
• For in- and outdoor use        
• Suitable for almost all subfloors
• Watertight (when applied as an impervious layer)   
• Flexible
• Moisture- and frost-resistant
• Very suitable for tiles with an absorption capacity of 1% or less
• High initial adhesion strength
• High final bond strength
• For wall and floor
• Suitable for underfloor heating

• For the flexible and water-resistant fixing of wall and floor tiles, mosaic and flat dark coloured natural stone, various ceramic tiles, flagstones, split tiles, porcelain stoneware tiles and other tiles with an minor absorption capacity on almost any type of subfloor e.g. concrete, wood, old tiles, granito, underfloor heating etc.
• Very suitable for application in the “wet areas”, swimming pools and outdoor use.
• For fixing glass-mosaic and light-coloured natural stone, such as marble. For these applications we recommend 711 Uniflex or 681 Marmercol. 

• The subfloor must have a good tensile and compression strength. The subfloor should also be smooth, dry and free from grease, dirt and dust. 
• When using the adhesive outdoors apply two layers of 740 Isoflex 2K. Also remove all old ceramic finishing.
• Wooden floors, made of floorboards, should be sufficiently supported underneath (distance between the beam maximum 60 cm). To attain a fixed construction screw water-resistant plywood (minimum 12 mm thickness) on top of this layer. Thereafter apply 099 Dispersion Primer and prime completely with 685 Eurocoat. Maximum tile size 30x30 cm.
• Prime moisture-sensitive or absorbent subfloors e.g. gypsum-based walls wit 099 Dispersion Primer. Apply 685 Eurocoat in the shower area to attain an impervious layer between the tile adhesive and subfloor.
• Prime self-levelling anhydrite floors with a residual construction moisture percentage of 0.5% with 099 Dispersion Primer (drying time minimum 12 hours).
• In advance always seek our technical data sheets. In doubt about the application ask for technical advice. 

• Add 25 kg of 705 Watertight Tile Adhesive to approx. 6 litres of cool and clean tap water and stir the mortar for 1 minute, by using an electric stirrer (approx. 600 rpm), to a smooth and homogeneous mixture.
• After strirring wait for a few minutes, stir once again and apply the adhesive on the subfloor with the recommended adhesive spreader.
• Press the tiles within 15 to 20 minutes with a shuffling movement into the adhesive. Check regularly to ensure that the back of the tile is in full contact with the adhesive. Remove excess adhesive immediately from the joints.
• For the watertightness on floors in wet areas first apply an impervious layer of approx. 5 mm thickness with a flat trowel. Thereafter make adhesive strips with the recommended adhesive spreader. When it is absolutely necessary to obtain a water-resistant layer, make two actions. First apply an impervious layer of approx. 3 mm thickness with a flat trowel and let dry for minimum 5 hours. Thereafter apply a second layer and make adhesive strips.
• In dry areas make the adhesive strips with the recommended adhesive spreader in the usual way.
• Apply the mixed adhesive within 60 minutes. Do not add extra water!
• Under normal circumstances, i.e. a temperature of 20 °C and a relative humidity of 65%, the joints may be filled after minimum 24 hours. 

Environment and health

• Environmental Product Declaration EPD-NIBE-20210224-17685 verified by SGS Search / Intron.
• Low dust with dust factor < 5% components with a particle size of < 2 μm (micrometer).
• Tested for emission of volatile organic compounds and has tested EMICODE EC 1PLUS according to EN 13999-2/4.
• Meets the criteria of BREEAM-NL HEA 9 Volatile organic compounds; promoting a healthy and good indoor air quality because the construction and finishing materials used cause low emissions of harmful volatile organic compounds and other harmful substances. Suitable for BREEAM new construction and renovation.