• Applicable with spray 
• Acid- and heat-resistant
• Watertight 
  
• For in- and outdoor use
• Suitable for almost all subfloors
• Joint width from 1.5-12 mm
• High final bond strength
  

• For the acid- and heat-resistant grouting of ceramic floor and wall tiles on sinks, laboratory tables, industrial floors that will be affected by chemicals etc.
• Also very suitable for extreme moist areas, e.g. sanitary areas, professional kitchens and swimming pools.
• Also suitable as thin bed adhesive for wall and floor applications.
• 358 Toolcleaner can be used for removing epoxy veil and spots on ceramic wall and floortiles.

Depending on the size of the tile, joint width and depth. The following formula will enable you to calculate the required quantity of grouting cement per m²: 

Directions for use grouts:

• The joints should be clean, dry and free from grease and dust.
• Follow the directions by “working temperature” of the “technical facts”. Do not grout on subfloors that are strongly warmed through e.g. sunlight. The firs two days after application the temperature may not drop under 12 °C.
• Grout the fixed tiles after approx. 24 hours. Tiles fixed with a sand/cement mortar can be grouted after minimum 3 days (depending on the drying process of the mortar).
• Add component A and B completely together and mix for minimum 3 minutes with an electric stirrer to a smooth and homogenous mixture. If only part of the packaging is to be used, add approx. 3 parts of resin to 1 part of hardener. Take care that insufficient mixing can cause permanent sticky parts in the joint, which will not bond completely. In case of wall applications add 1 bag of consistency adjuster before mixing.
• Apply the mixture immediately with a rubber spatula or spout into the joints. Remove excess material immediately in diagonal direction.
• After removing the excess material, emulsify grouting residues with as little water as possible, with an epoxy cleaning sponge and warm water. Thereafter clean tiles with a viscose sponge. Wait with cleaning until the joints have dried. Waiting time is 1-5 hours, depending on temperature and relative humidity. Especially clean anti-skid and non-glazed tiles completely before hardening.
• Remove any present epoxy veil on glazed tiles within 6 hours after application by cleaning with spirits. After curing, remove possible epoxy veil with 358 Toolcleaner.
• After grouting wait at least 16 hours before walking on the floor.
  

Directions for use thin bed adhesive:

• The surface must be clean, free of grease and dust, dry, pressure and tear resistant, in accordance with the requirements, as stated in DIN 18 532.
• Properly observe the instructions regarding the procesing temperature of the technical properties. Do not apply adhesive to substrates that become very hot e.g. through solar radiation. The first two days after application the temperature may not drop below 12 °C.
• Slightly sanding screeds must be primed using 021 Euroblock Reno.
• Add all the resin and hardener components together and mix the paste with a spiral mixer for 3 to 4 minutes to a lump free, homogeneous compound. Important: if the compound has not been mixed sufficient, sticky lumps will arise in the adhesive which will not bind entirely.
• Apply grooves with the trowel and place the tiles within 10-15 minutes in a sliding motion in the fresh bed of adhesive and press firmly. Always check that the back of the tiles is in contact with the adhesive entirely. Excess adhesive must be removed from the joints immediately.
• At a temperature of approx. 20 °C the tiles can be grouted after 1 to 2 days, depending on the circumstances.
• The mixed adhesive must be processed within 60 minutes.
• After the adhesive has been applied, the floors cannot be walked on for at least 24 hours.

General:

• Clean tools immediately after use with warm water.
• You are advised to wear rubber gloves when processing the adhesive. Thoroughly wash with water and soap in the event of skin contact.
• In advance always seek our technical data sheets. In doubt about the application ask for technical advice.