Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2



Very low emission and powerful dispersion-based contact adhesive with a strong adhesion.

  • 650-safety data sheet uk.pdf

    650-safety data sheet uk.pdf

  • 650-ec 1 plus licence uk.pdf

    650-ec 1 plus licence uk.pdf

  • pdf-product-specification.pdf


Product Typification

Very low emission and powerful dispersion-based contact adhesive with a strong adhesion.
Basis : Superior polymer dispersion.
Colour : Cream.
Consistency : Thick liquid.

Product advantages:
  • Very low emission
  • Emicode EC 1 PLUS
  • Powerful enough to bear high tensions
  • High initial adhesion strength
  • Reactivate through warmth
  • Tool included 


Consumption : 500 g/m² per two coats.
Flammability : Non-flammable.
Frost resistance : No.
Specific weight : 1.36 kg/l.



For the two-sided fixing of:

  • carpet on stairs
  • PVC nosing
  • PVC adhesive skirting
  • rubber nosing
  • hollow skirting of hard floor covering
  • cork floor covering
  • wall covering with a foamed back for sport halls.

Working Process

Storage : Store cool and free from frost. Recommended temperature between 15 - 25 °C.
Tools : Texture roller (included).
Open time : After drying of the adhesive approx. 4 hours.*
Latency : After total drying of the adhesive place adhesive parts together.
Drying time : 24 hours.*
Drying : Depending on temperature and relative humidity. Drying time at an airflow of approx. 20 °C is approx. 20 minutes. Drying time without a device is 1 - 2 hours.*
Shelf Life : 12 months, in unopened packaging.
Cleaner : Water.
Application temperature : 
Frost-proof : No.
Remarks : 

Technical information and safety data sheets of any laying materials and floor coverings used must be observed! The instructions of the respective profile manufacturers must be observed, especially when gluing stair nosing edges.

In case of doubt, the surface to be bonded must be degreased/cleaned of exudates.

* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

500 g/m² per two coats.

  • 650 Eurostar Fastcol is suitable for any type of subfloor that has a good tensile and compression strength.
  • The subfloor should also be even, clean, permanently dry and free from grease and dirt, and other pollutions according to the requirements of BS 8203 or DIN 18 365.
  • In advance always seek our technical data sheets. In doubt about the application ask for technical advice.

User manual:

Before use, temper the product according to the processing conditions.

Stir before use!

  • Apply the adhesive on the material and the subfloor (e.g. stairs, PVC, rubber) with the enclosed texture roller and let dry completely.
  • Drying time of the adhesive can considerably be reduced to approx. 20 minutes by using a ventilator with an fan of approx. 20 °C. Without a device the drying time is 1 - 2 hours at 20 °C.
  • After drying of the adhesive the open time is still approx. 4 hours.
  • It is possible to pre-roll the material approx. 4 days before fixing. On the day of fixing roll the subfloor with 650 Eurostar Fastcol and let dry.
  • In case both adhesive layers are dry and the open time has expired an optimal adhesion can be realised by heating these adhesive layers with e.g. a welding dryer, infrared radiator or gas flame for a short period.
  • Place both heated adhesive parts together and press carefully.
  • Afterwards it is possible to make adjusments by heating the material are again and subsequently press carefully.
  • The adhesion of the fixing depends on the application of sufficient adhesive (texture roller).
  • Remove fresh adhesive spots immediately with water.

Working conditions:
Required surrounding temperature : 18 - 23 °C.
Temperature for material and subfloor : min. 15° - max. 20 ºC.
Relative humidity : 40 - 80%.

Underfloor heating systems:
650 Eurostar Fastcol can be applied on underfloor heating systems. The startprotocol of the floorheating needs to be completly executed in accordance with the directives of the supplier. Turn off the heater 24 hours before installation. Do not heat again until at least 24 hours after installation, in steps of maximum 5 °C water temperature per day.

Contains methylchloroisothiazolinone and  methylisothiazolinone (3:1) and benzisothiazolinone. May produce an allergic reaction.

Environment and health

Hazard Class : None.
Safety and environment : Safety data sheets of Forbo Eurocol products according to EEG-guideline 91/155. Keep out of reach of children. Do not eat, drink or smoke while processing the product. Only give completely empty containers for recycling. Material residues can be disposed of as household waste.
MSDS : For extensive information about safety and environment we refer to our website
Substances causing allergy : Contains 1,2-benzisothiazol-3(2H)-one, reaction mass of: 5-chloro-2-methyl-4-isothiazolin-3-one [EC no. 247-500-7] and 2-methyl-2H-isothiazol-3-one [EC no. 220-239-6] (3:1). May produce an allergic reaction.


Texture roller with synthetic holder included.

Article Definition Packaging EAN-code
650Eurostar Fastcol 7.5 kg Bucket 8 710345 650106