640 EUROSTAR SPECIAL

eurocol
640 EUROSTAR SPECIAL

Fast-grabbing adhesive with a longer open time and longer final tack than 540 Eurosafe Special, suitable for bonding PVC floor coverings in sheets, planks and tiles, cushion vinyl, Marmoleum Decibel and carpet with a PVC backing. Also suitable for bonding smooth floor coverings, such as rubber flooring in sheets (e.g. Noraplan). Onyx wall coverings can also be installed using this adhesive. Wet, semi-wet and dry bonding are all possible with this adhesive; the choice depends on the application and conditions. Also suitable for use on ships where IMO certification is required. Thanks to EMICODE EC 1PLUS (very low emissions), it is also suitable for BREEAM projects. Suitable for indoor use.

epdfeica-640 eurostar special-uk.pdf
640-safety data sheet uk.pdf
epd_deklaration 640_uk.pdf
640-ec 1 plus licence uk.pdf
640-imo module b uk.pdf
pdf-product-specification.pdf

Product Typification
Fast-grabbing adhesive with a longer open time and longer final tack than 540 Eurosafe Special, suitable for bonding PVC floor coverings in sheets, planks and tiles, cushion vinyl, Marmoleum Decibel and carpet with a PVC backing. Also suitable for bonding smooth floor coverings, such as rubber flooring in sheets (e.g. Noraplan). Onyx wall coverings can also be installed using this adhesive. Wet, semi-wet and dry bonding are all possible with this adhesive; the choice depends on the application and conditions. Also suitable for use on ships where IMO certification is required. Thanks to EMICODE EC 1PLUS (very low emissions), it is also suitable for BREEAM projects. Suitable for indoor use.

Basis : Superior acrylic dispersion.

Colour : Beige.

Consistency : Thick liquid.

Product advantages:

EMICODE EC 1PLUS (very low emmission)
Non-flammable
Multi-purpose application
Easy to apply
Favourable spreading capacity
Short waiting time
Very long open time
Very high stickiness
High final adhesion strength
Odour neutral
Roller-castor-chair resistant

Performances

Classification	:	GEV-EMICODE EC 1PLUS (very low emissions) tested in accordance with EN 13999-2/4. Suitable for BREEAM projects.
Consumption	:	225 - 275 g/m².
Curing	:	48 hours.*
Flammability	:	Non-flammable.
Specific weight	:	1.25 kg/l.

Application
For installing:
PVC floor covering in sheets and tiles
cushion vinyl
PVC backed carpet
rubber floor covering with a smooth back in sheets and tiles
polyolefin floor covering
Marmoleum Decibel
Onyx wall covering

Working Process

Tools	:	852 Notched trowel / A2 notch
Open time	:	Approx 10 - 120 minutes.*
Waiting time	:	Approx 10-50 minutes.*
Curing	:	48 hours.*
Storage	:	Cool and dry, well sealed at normal temperature (5° - 30 °C).
Shelf Life	:	15 months, in unopened packaging.
Cleaner	:	Water.
Sensitive to frost	:	Yes.
Remarks	:	Technical information and safety data sheets of any laying materials and floor coverings used must be observed! Allow floorings to air condition in the rooms before laying. The coverings must be relaxed and laid flat. During the setting phase, the direct influence of heat/solar radiation, dynamic and point loads must be avoided. Do not weld the coverings until the following day at the earliest. In order to minimise residual impressions as far as possible, resilient floor coverings should always be placed in the wet adhesive bed and immediately rubbed down well to completely crush the adhesive ridges. If the insertion time is exceeded, during which the adhesive grooves can still be completely squashed, standing grooves remain which can mark the top side of thin coverings or be squashed under point loads. This leads to visible deformations in the floor covering structure. The work progress is to be set up in such a way that a flash-off time, at wetting of the reverse side of the flooring is guaranteed, is not exceeded. With regard to such markings any claims arising therefrom are excluded. In the case of textile coverings, attention must be paid to the dimensional stability when exposed to moisture (shrinkage). When bonding textile coverings without fillers, a flash-off time of approx. 20 minutes must be observed to prevent the still wet adhesive from "sticking" into the back of the covering. EMICODE, further information at www.emicode.com. Wear protective gloves / eye protection.

* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

Consumption:
225 - 275 g/m².

Substrate:

640 Eurostar Special is suitable for any type of subfloor that has a good tensile and compression strength. The subfloor should also be even, clean, permanently dry and free from grease and dirt, according to the requirements of BS 8203 or DIN 18 365.
When installing on impervious subfloors apply a 2 mm levelling compound layer.
In advance always seek our technical data sheets. In doubt about the application ask for technical advice.

User manual:

In most cases, apply the adhesive with a fine-toothed adhesive comb (Eurocol 852 adhesive comb/toothed A2). Type of spreader depends on the type of floor covering and condition of the subfloor.
The adhesive can be used for wet, semi-wet, dry or contact bonding.
Under “normal” climatic conditions (20 °C and 65% humidity), wait for at least 10 minutes
Immediately after bonding roll the floor covering carefully. Sheet-ends and longitudinal joints are to be pressed firmly.
Rolling and pressing should be repeated after approx. 30 - 45 minutes.
Remove fresh adhesive spots immediately with water.
Clean tools with water immediately after use

Working conditions:
Required surrounding temperature : 18 - 23 °C.
Temperature for material and subfloor : min. 15° - max. 20 ºC.
Relative humidity : 40 - 75%.

Further information:

Keep out of reach of children.
Keep area thoroughly ventilated during and after processing and drying.
When processing do not eat, drink or smoke.
Avoid contact with eyes and skin and use suitable protective equipment.
In case of contact with eyes or skin, rinse immediately with plenty of water.
Dispose of product residues and cleaning water in accordance with local environmental regulations and do not dispose of them in the sewer.
Only submit packaging without residues for recycling. Dried material remains can be disposed of with household waste.
For detailed information about the safety measures, we refer to the safety information sheet on our website www.eurocol.nl.
The product contains mixture of: 5-chloro-2-methyl-2H-isothiazol-3-one [EC no. 247-500-7] and 2-methyl-2H-isothiazol-3-one [EC no. 220-239 -6] (3:1), 1,2-benzisothiazol-3(2H)-one. May cause an allergic reaction.

Underfloor heating:
640 Eurostar Special can be applied on underfloor heating. . The startprotocol of the floorheating needs to be completly executed in accordance with the directives of the supplier. Turn off the heater 24 hours before application. Turn off the heater 24 hours before application. Do not heat again until at least 48 hours after installation, in steps of maximum 5 °C water temperature per day. Make sure that the floor temperature does not exceed 29 °C.

Quality and guarantee

Environment and health

GISCODE	:	D1
LEED	:	VOC 0 g/l, meets: IEQ Credit 4.1
DGNB	:	VOC 0 %, quality level: 4
Hazard Class	:	None.
Safety and environment	:	Safety data sheets of Forbo Eurocol products according to EEG-guideline 91/155. Keep out of reach of children. Do not eat, drink or smoke while processing the product. Only give completely empty containers for recycling. Bound material residues can be disposed of as household waste.
MSDS	:	For extensive information about safety and environment we refer to our website www.eurocol.nl.
Substances causing allergy	:	Contains 1,2-benzisothiazol-3(2H)-one, reaction mass of: 5-chloro-2-methyl-4-isothiazolin-3-one [EC no. 247-500-7] and 2-methyl-2H-isothiazol-3-one [EC no. 220-239-6] (3:1). May produce an allergic reaction