Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2



Fixation, for the non-skid installation of carpet tiles and loose-lay PVC floors or floors with a PVC backing.

  • 542-imo module b uk.pdf

    542-imo module b uk.pdf

  • 542-safety data sheet uk.pdf

    542-safety data sheet uk.pdf

  • licence_542-tack plus_eco product declaration_uk.pdf

    licence_542-tack plus_eco product declaration_uk.pdf

  • 542-ec 1 plus licence uk.pdf

    542-ec 1 plus licence uk.pdf

  • pdf-product-specification.pdf


Product Typification

Fixation for the non-skid installation of carpet tiles and loose-lay PVC floors or floors with a PVC backing.
Basis : Acrylic dispersion.
Colour : White.
Consistency : Liquid.

Product advantages:
  • very low emission
  • Emicode EC 1PLUS
  • Non-flammable 
  • Easy removal   
  • Favourable spreading capacity 
  • Permanent adhesion 


Colours : Белый
Colours : Белый
Consumption : On impervious subfloors : 50 - 100 g/m².
On porous subfloors : 100 - 150 g/m². 
Flammability : Non-flammable.
Frost resistance : No.
Specific weight : 1.04 kg/l.


  • For the removal and non-skid installation of carpet tiles on smooth subfloors. 
  • Also suitable for fixing the sound insulating declutching mat 820 DIM Floor.
  • Can also be used to fixate loose-lay PVC floors or floors with a PVC backing.

Working Process

Tools : Lambswool roller or brush. Can be sprayed.
Waiting time : Approx 60 minutes.* After application wait for the material to set-off (get transparent).
Storage : Store cool and free from frost.
Shelf Life : 12 months, in unopened packaging.
Cleaner : Water.
Frost-proof : No.
Remarks : 

Technical information and safety data sheets of any laying materials and floor coverings used must be observed!

Allow floorings to air condition in the rooms before laying. The coverings must be relaxed and laid flat.
During the setting phase, the direct influence of heat/solar radiation, dynamic and point loads must be avoided.

When laying there is no guarantee that the coverings will be able to resume without sticking.
If the flooring is laid on existing flooring, the possibility of changes in the colour of the flooring cannot be excluded.
Removing the fixings from existing floor coverings can lead to damage to these coverings.
A possible joint formation of the flooring can also be reduced by the application of a fixation.

EMICODE, further information at

* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

On impervious subfloors : 50 - 100 g/m².
On porous subfloors : 100 - 150 g/m². 

  • 542 Eurofix Tack Plus is suitable for any type of subfloor that has a good tensile and compression strength.
  • The subfloor should also be even, clean, permanently dry and free from grease and dirt, according to the requirements of BS 8203 or DIN 18 365. 
  • Application is also possible on old and smooth floor covering, such as linoleum. Before application degrease the old floor covering thoroughly. 
  • In advance always seek our technical data sheets. In doubt about the application ask for technical advice. 

User manual:
  • Apply 542 Eurofix Tack Plus equally in the recommended quantity on the subfloor with a lambswool roller or brush. This product can also be sprayed.
  • Apply the carpet tiles or loose-lay floor system as soon as 542 Eurofix Tack Plus sets-off (gets transparent). Depending on temperature, relative humidity and subfloor the waiting time is approx. 60 minutes.
  • Wait for 20-30 minutes before fixing the 820 DIM Floor mats. Then roll carefully and rub well.
  • Remove fresh adhesive spots immediately with water.

Working conditions:
Required surrounding temperature : 18 - 23 °C.
Temperature for material and subfloor : min. 15° - max. 20 ºC.
Relative humidity : 40-80%. 

Underfloor heating systems:
542 Eurofix Tack Plus can be applied on underfloor heating systems. The startprotocol of the floorheating needs to be completly executed in accordance with the directives of the supplier.Turn off the heater 24 hours before fixation. Do not heat again until at least 24 hours after fixation, in steps of maximum 5 °C water temperature per day.

Quality and guarantee

Environment and health

Hazard Class : None.
Safety and environment : Safety data sheets of Forbo Eurocol products according to EEG-guideline 91/155. Keep out of reach of children. Do not eat, drink or smoke while processing the product. Only give completely empty containers for recycling. Material residues can be disposed of as household waste.
MSDS : For extensive information about safety and environment we refer to our website
LEED : VOC 0 g/l, meets - erfüllt: IEQ Credit 4.1
Substances causing allergy : Contains 1,2-benzisothiazol-3(2H)-one, mixture of: 5-chloro-2-methyl-4-isothiazolin-3-one [EC no. 247- 500-7] and 2-methyl-2H-isothiazol-3-one [EC no. 220-239-6] (3:1). May produce an allergic reaction.


542Eurofix Tack Plus10 kg jerry can8 710345 542104