Choose your country

Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2

Series 5

Side flexing and spiral belts
Pitch 25 mm (0.98 in)
Belts for light to medium-duty food and non-food applications


Series 5 – Excerpt from Prolink Engineering Manual

Design characteristics

  • Suitable for both straight and radius conveying
  • up to 45 % open area for excellent air circulation
    and drainage
  • Stainless steel hinge pins for high load capacity,
    lateral stiffness, fewer belt supports and minimum belt lifting in curves
  • No potential belt edge catch points due to safe fixing of hinge pins

Series 5 - Design characteristics

Basic data

Pitch 25 mm (0.98)
Belt width min.100 mm (3.9 in), 175 mm (6.9 in) for S5 ST
Width increments25 mm (0.98)
Hinge pinsStainless steel

Prolink Series 5 Basic Data

S5-45 GRT | 45 % Opening | Grid top

  • Open area (45 %) for excellent air circulation and drainage
  • Lattice shaped surface

S5-45 GRT

S5-45 NTP | 45 % Opening | Nub top (round studs)

  • Open area (45 %) for excellent air circulation and drainage
  • Lattice shaped surface with 3.0 mm (0.12 in) high round studs and 8 % contact area
  • Side modules without NTP-surface

S5-45 NTP

S5-39 FRT1

  • Excellent air circulation and drainage
  • Integrated friction pads (raised) increase surface friction and provide gentle grip
  • Side modules without FRT-surface

S5-39 FRT1

S5-33 FRT2 | 33 % Opening | Friction top (Design 2)

  • Open area (33 % for full FRT2 surface area) for excellent air circulation and drainage
  • Integrated friction pads (flat) provide gentle grip

S5-33 FRT2

S5-45 GRT G | 45 % Opening | Grid top · guided

  • Excellent air circulation and drainage
  • Lattice shaped surface and Hold Down tabs
  • Allows utilisation of the entire belt width

S5-45 GRT G

S5-45 NTP G | 45 % Opening | Nub top (round studs) · guided

  • Excellent air circulation and drainage
  • With round studs for increased grip (8 % contact area)
  • Allows utilisation of the entire belt width
  • Side modules only available without NTP-pattern

S5-45 NTP G

S5-39 FRT1 G | 39 % Opening | Friction top (Design 1)

  • Excellent air circulation and drainage
  • Integrated friction pads (raised) increase surface friction and provide gentle grip
  • Allows utilisation of the entire belt width
  • Side modules without FRT-surface

S5-39 FRT1 G

S5-33 FRT2 G | 33 % Opening | Friction top (Design 2)

  • Open area (33 % for full FRT2 surface area) for excellent air circulation and drainage
  • Integrated friction pads (flat) provide gentle grip
  • Allows utilisation of the entire belt width
  • Side modules without FRT-surface

S5-33 FRT2 G

S5-45 GRT RG | 45 % Opening | Grid top · reversed guided

  • Excellent air circulation and drainage
  • Lattice shaped surface and reversed Hold Down tabs
  • Allows utilisation of the entire belt width

S5-45 GRT RG

S5-45 NTP RG | 45 % Opening | Nub top (round studs) · reversed guided

  • Excellent air circulation and drainage
  • With round studs for increased grip (8 % contact area)
  • Allows utilisation of the entire belt width
  • Side modules only available without NTP-pattern

S5 45 NTP RG

S5-39 FRT1 RG | 39 % Opening | Friction top (Design 1)

  • Excellent air circulation and drainage
  • Integrated friction pads (raised) increase surface friction and provide gentle grip
  • Allows utilisation of the entire belt width
  • Side modules without FRT-surface

S5-39 FRT1 RG

S5-33 FRT2 RG | 33 % Opening | Friction top (Design 2)

  • Open area (33 % for full FRT2 surface area) for excellent air circulation and drainage
  • Integrated friction pads (flat) provide gentle grip
  • Allows utilisation of the entire belt width
  • Side modules without FRT-surface

S5-33 FRT2 RG

S5-45 GRT ST | 45 % Opening | Grid top · strong

  • Excellent air circulation and drainage
  • Lattice shaped surface
  • Version with reinforced brick-laid side modules (75 mm/2.9 in and 100 mm/3.9 in) increases belt pull capacity

S5-45 GRT ST

S5-45 NTP ST | 45 % Opening | Nub top (round studs) · strong

  • Excellent air circulation and drainage
  • With round studs for increased grip (8 % contact area)
  • Version with reinforced brick-laid side modules increases belt pull capacity
  • Side modules only available without NTP-pattern

S5-45 NTP ST

S5-39 FRT1 ST | 39 % Opening | Friction top (Design 1)

  • Excellent air circulation and drainage
  • Integrated friction pads (raised) increase surface friction and provide gentle grip
  • Reinforced side modules increase belt pull capacity
  • Side modules without FRT-surface

S5-39 FRT1 ST

S5-33 FRT2 ST | 33 % Opening | Friction top (Design 2) · strong

  • Open area (33 % for full FRT2 surface area) for excellent air circulation and drainage
  • Lattice shaped surface
  • Version with reinforced brick-laid side modules increases belt pull capacity

S5-33 FRT2 ST

Sprockets

in different sizes with round or square sprocket bore

Series 5 - Sprockets

Profiles

in different heights and designs for inclines

Series 5 - Profiles

Side guards

in different heights for retention of bulk products

Series 5 - Side guards

Ball-bearing modules

to minimize friction forces at the belt edge

Series 5 - Ball-bearing modules
Combo Belts Teaser EN

Further Information

  • 888 Series 5 EN – Excerpt from Prolink engineering manual

    Series 5
    Excerpt from Prolink Engineering Manual