SelectYourLanguage

Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2

eurocol
8802 EUROFILLER WOOD PLUS

8802

Wood filler solution, waterbased, for joints up to 2 mm width.

8802-eurofiller-wood-plus.jpg
  • pdf-product-specification.pdf

    pdf-product-specification.pdf

  • licence_8802 wood plus_ec1plus_2020 uk.pdf

    licence_8802 wood plus_ec1plus_2020 uk.pdf

  • safety data sheet_eurocol_8802_eurofiller_wood_plus_uk.pdf

    safety data sheet_eurocol_8802_eurofiller_wood_plus_uk.pdf

Product Typification


Basis : PUR - PVAc dispersions, pre-filled
Colour : White.
Consistency : Thick liquid.

Product advantages:
  • Prefilled dispersion-based wood filler solution, mixable with sanding dust of all wood types (K80 - 100).
  • For filling joints in fully bonded parquet up to 2 mm.
  • Long working time.
  • Dries very quickly in the joint.
  • Excellent stability in the joint.
  • Can be sanded very well, putty residues are visible on the wood surface.
  • Odourless.
  • To be used before using Eurocol surface materials.
  • For interior use.
  • The product can be used on underfloor heating.
  • Very low emission installation material, EMICODE EC 1 Plus.
  • Declared by baubook, "ecological building product".

Performances

Consumption : approx. 50 - 100 ml/m² depending on the joint width.
Flammability : Non-flammable.
Frost resistance : No.
Specific weight : 1,02 g/cm³

Application

Application:
For filling joints in fully bonded parquet.

Working Process

Storage : Store cool and dry in unopened packaging.
Tools : Spatula.
Drying : Approc 30 - 60 minutes. *
Shelf Life : 12 Months, in unopened packaging.
Cleaner : Water.
Frost-proof : No.
Remarks : 

Observe the technical information and safety data sheets of other installation materials and the parquet manufacturer!

In the case of unknown types of wood, the suitability of the products to be used should be checked by preliminary tests.

Nailed or screwed parquet floors are usually not puttyled to avoid breakouts of the putty due to the movable construction.

If the joint edges are very dirty or waxed, adhesion problems can occur.

EMICODE, further information at www.emicode.com.


* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

Consumption:
approx. 50 - 100 ml/m² depending on the joint width.

Substrate:
  • The surfaces to be sealed must be clean and free of residues of oil, wax, silicone and other adhesion-reducing layers.
  • The wood surface is roughly sanded.


User manual:

Before use, temper the product according to the processing conditions.

  • Stir well and thoroughly before use.
  • Mix the solution with approximately 15 % of sanding dust of the same wood as the parquet floor (grit: 80 – 120) to an easily applicable paste (consistency similar to dough).

If the consistency of the mixture is too thick, the wood putty mix will not sick well in the joint and
may separate while sanding. If the consistency of the mixture is too wet, the joints may not be filled 100%. The finer the sanding dust, the better is the filling ability and the adhesion in the joint.

  • We recommend mixing the solution with sanding dust in a clean bucket to a homogenous mixture and not on the floor! Too much sanding dust can lead to cracks not being filled sufficiently, please reduce the dust quantity.
  • Apply the mixture on the whole parquet floor equally diagonal with a rust free double sided spatula and push the material into the joints forcefully. Repeat the procedure to fill the joints if necessary.
  • After a drying time of approximately. 30 – 60 min., grind the floor and continue with find grinding.
    Make sure that no residues of the wood-putty mixture remain on the surface.
    In most cases, finely grinding with grit 100 is sufficient.

Now you can start sealing the parquet with all types of Eurocol parquet varnishes, parquet oils or parquet oil-waxes.

Processing conditions: 

at least 15 °C floor temperature,
at least 18°C material and room temperature,
35-75% relative humidity, recommended <65%.





Quality and guarantee

Environment and health

Hazard Class : None.
Safety and environment : Safety data sheets of Forbo Eurocol products according to EEG-guideline 91/155. Keep out of reach of children. Do not eat, drink or smoke while processing the product. Only give completely empty containers for recycling. Material residues can be disposed of as household waste.
MSDS : For extensive information about safety and environment we refer to our website www.eurocol.nl.
GISCODE : W2+
LEED : VOC 16,5 g/l, meets - erfüllt: IEQ Credit 4.1
DGNB : VOC 1,62 %, quality level - Qualitätsstufe: 3
Substances causing allergy : Contains 2-methyl-2H-isothiazol-3-one, 1,2-benzisothiazol-3(2H)-one. May produce an allergic reaction.


Articles

artikelproductnamepackagingshipping unit
8802Eurofiller Wood Plus PE bucket à 5 kg72/pallet
8802Eurofiller Wood Plus PE bucket à 10 kg44/pallet