SelectYourLanguage

Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2

eurocol
869 EUROFINISH OIL WAX DUO

869

Two-component impregnation oil, for extreme high traffic areas, enables fast walkability of sealed floor.

869_2017.jpg
  • pdf-product-specification.pdf

    pdf-product-specification.pdf

  • safety data sheet_eurocol_869_a_uk.pdf

    safety data sheet_eurocol_869_a_uk.pdf

  • safety data sheet_eurocol_869-hardener_uk.pdf

    safety data sheet_eurocol_869-hardener_uk.pdf

Product Typification


Basis : Combination of oils with isocyanate hardener.
Colour : Yellow.
Gloss : silk mat
Consistency : Pasty.

Product advantages:
  • Extremely fast resistant, solvent- and water-free 2-component impregnating oil, which sets by chemical hardening. 
  • For surface impregnation of all types of parquet and wood, as well as cork.
  • Can be used as a water-free primer with good barrier properties against wood ingredients under approved Eurocol Aqua lacquers.
  • Excellent for the object area with extreme stress.
  • Achieves an open-pored and silk-matt surface that is easy to clean.
  • High mechanical and chemical resistance to household chemicals.
  • Economical consumption is achieved through the application of the filler.
  • The oiled surface can be walked on after only 4 hours for initial use.
  • The fast drying process allows the use even with critical wood species, which usually cause a delay in drying.
  • For interior use.
  • The product can be used on underfloor heating.
  • Emission tested building product according to DIBt principles.

Performances

Consumption : approx. 25 -35 ml/m² depending on the type of wood and the nature of the substrate (end-grain wood, lying fibres...).
Range of a container 1 l: approx. 30 - 40 m² for a coating with spatula.
Curing : First careful use after 24 hrs.
Flammability : Non-flammable.
Frost resistance : yes.
Passableness : First careful use after 4 hrs.
Special quality : Quick drying, recoatable.
Specific weight : 0,97 g/cm³

Application

Application:
For impregnation and maintenance of wooden floors.

Working Process

Storage : Store cool and dry in unopened packaging.
Tools : Spatula
Processing time : Use within 4 - 6 hrs. after mixing.*
Drying : Application with spatula appr. 30 - 60 minutes.
Shelf Life : 24 Months, in unopened packaging.
Frost-proof : yes.
Remarks : 

Technical information and safety data sheets of other installation materials and parquet must be observed!
If there is a delay in drying due to lower temperatures, inadequate ventilation, certain types of wood, wait until it is completely dry!

Also in the case of exotic woods that are subject to a delay in drying due to ingredients (e.g. Doussie/Afzelia, Jatoba, Kambala-Iroko, Meranti, Merbau) or even critical wood species such as Ipe, Afrormosia, Mahogany, Brazilian Walnut, Rosewood and Wenge can be used. Here the drying time can be increased.
According to DIN 18356, impregnated parquet floors must be continuously maintained. For this purpose we recommend Eurocol, the cleaning and care products designated for oiled floors. Observe special care instructions and provide the user with evidence of this.
Wash or water cloths or pads soaked with the liquid product immediately after use or store them in an airtight metal container. Risk of spontaneous combustion!
Not a consumer product according to 1999/EG/44.


* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

Consumption:
approx. 25 -35 ml/m² depending on the type of wood and the nature of the substrate (end-grain wood, lying fibres...).
Range of a container 1 l: approx. 30 - 40 m² for a coating with spatula.

Substrate:
  • The surfaces to be sealed must be clean and free of residues of oil, wax, silicone and other adhesion-reducing layers.
  • Joints are closed with suitable Eurocol joint sealant.
  • The fine sanding depends on the type of wood. The surface and edge sanding must be levelled with a sanding grid.
  • In order to ensure the penetration of the product, a "tight sanding" of the surface with too fine sanding paper must be prevented.


User manual:

Before use, temper the product according to the processing conditions.

  • Stir well before use!
  • Add the hardener and mix both components carefully together until a streak-free, homogeneous mixture is obtained.
  • The sanded and cleaned wooden floor should be applied generously in sections using a double-sided trowel (recommended with rounded corners) and then evenly smoothed off. In case of less absorbent and/or dense woods, the application quantity must be lowered in order to achieve a stick-free, even drying. 
  • After approx. 30 - 60 minutes of oil penetration, polish out the wax parts with a single-disc machine with a motor power of at least 1 kW (green pad), thus evenly distributing and removing excess material.
    This way an even drying is achieved. Excess material that is not polished out will delay drying and lead to differences in gloss. Finally, equalise the surface with a single disc machine with white pad.
  • If the polishing pad is saturated with excess material, continue polishing on uncoated, raw wood until the pad is reabsorbent or replace the pad.
  • On highly absorbent surfaces (e.g. beech/ash, wood-block paving, high-edge lamellas), apply further coats depending on the absorbency of the wood and level out in the same way.
  • If drying is delayed due to lower temperatures, inadequate ventilation, certain types of wood, wait until the wood is completely dry!
  • Before using suitable OSB boards, they must be sanded and de-dusted as far as possible. With cork and OSB boards, a longer drying time is to be expected due to the surface structure and the associated increased application quantity.
    Excess material applied causes slower drying of the surface and possibly slight surface stickiness.
    For this reason, carefully absorb any excess and, if necessary, treat these areas immediately with 879 Euroclean Oil (maintenance oil).

Damaged areas can be repaired after cleaning by re-oiling without sanding the surface.

Working conditions:
Required surrounding temperature: min. 18°C.
Material and subfloor temperature: min. 15°C.
Relative humidity: 35 - 75%, recommended <65%.

After a drying time of 16 to max. 48 hours, polish and vacuum the surface with a single-disc machine and green pad.
Afterwards, the surface can be recoated with approved Eurocol Aqua lacquers.





Quality and guarantee

Environment and health

Safety and environment : Safety data sheets of Forbo Eurocol products according to EEG-guideline 91/155. Keep out of reach of children. Do not eat, drink or smoke while processing the product. Only give completely empty containers for recycling. Material residues can be disposed of as household waste.
MSDS : For extensive information about safety and environment we refer to our website www.eurocol.nl.
GISCODE : Ö10+
LEED : VOC 0 g/l, meets - erfüllt: IEQ Credit 4.1
DGNB : VOC 0 %, quality level - Qualitätsstufe: 3
Substances causing allergy : Hardener: Contains isocyanates. May produce an allergic reaction.


Articles

articelproductnamepackagingshipping unit
869Eurofinish Oil Wax Duotin combi can à 1 l
1/box
240/pallet