Very high quality, universal, low-stress setting, self-levelling compound, cement-based.

For extreme loads.

Can be used in most applications without primer.

For levelling especially critical substrates such as waterproof, firmly bonded adhesive residues, mineral substrates, ceramic tiles, natural stone coverings, terrazzo, as well as standard mastic asphalt.

Can also be used with primer on new mineral substrates, on screwed wood-based panels (V100 P4 - P7, OSB 2 - 4).

Can also be used as substrate under Eurocol Surface products.

Also for the production of Eurocol FloorDesign floors in combination with Eurocol pigment powder and Eurocol Surface Finish.

Can be used in layer thicknesses up to 20 mm, on mastic asphalt up to 5 mm.

For subsequent flooring work and the laying of parquet.

Pumpable.

Squeegeeable.

Dust reduced.

• Favourable spreading capacity
• Self-smoothing
• Low-tension
• Excellent flow
• High compression strength
• Casein-free

The product can be used on underfloor heating and is suitable for use with chair castors in accordance with DIN EN 12529.

For indoor use.

Very low emission laying material, certified according to EMICODE EC 1 Plus.

For levelling critical and stony subfloors (interior use) in layers up to 20 mm.

• 990 Europlan Direct can be applied on any type of stony subfloor that is rigid and has a good tensile and compression strength. The subfloor should also be clean, permanently dry and free from grease and dirt, according to the requirements of BS 8203 or DIN 18 365/DIN 18356.
• In most cases it is not necessary to use a primer.
• Degrease smooth and impervious subfloors (tile floors, granito, terrazzo etc.) with 014 Euroclean/891 Euroclean Basic and and dry well. 
• Absorbent subfloors (sand/cement screeds) can be levelled with 990 Europlan Direct without a primer. 
• Prime very strong porous subfloors with 044 Europrimer Multi/044-1 Europrimer Multi Plus, 099 Dispersion Primer or 049 Europrimer ABS with a foam roller.
• Prime moisture sensitive subfloors (e.g. anhydrite, magnesite, water-soluble adhesive residues etc.) with 021 Euroblock Reno/021 Euroblock LE, 042 Eurobloick Turbo or 026 Euroblock Multi.
• In case of asphalt floors and bituminous substrates contact our technical department.
• Fill cracks and deep damages with 905 Europlan Fill or 945 Europlan Solid/940 Europlan Quick.
• After hardening prime 905 Europlan Fill or 945 Europlan Solid with 044 Europrimer Multi/044-1 Europrimer Multi Plus or 049 Europrimer ABS.
• Wooden floorboards must be of a good waterproof quality. During mixing of the 23 kg levelling mortar, add 250 g 811 Reno fibers. Minimum layer thickness must be 3 mm. Don`t devide the levelling mortar with a notched squeegee. Seams must be sealed up with 900 Europlan Reno or a suitable acrylic sealant. 
• Appropriately dimensioned Eurocol edge strips are to be used for rising building components.
• Fix cracks/seams in the subfloor with 021 Euroblock Reno in combination with 063 Eurotape and 846 Quartzsand or 808 Eurojoint Connector in combination with 021 Euroblock Reno. Alternatively with Europlan 913 Silicate sealing compound.
• Level anhydrite floors with 925 Europlan Alphy Direct or 920 Europlan Alphy.
• In advance always seek our technical data sheets. In doubt about the application ask for technical advice. 

• Add 23 kg of 990 Europlan Direct to 5.5 - 6 litres of cool and clean tap water.
• Stir thoroughly, using an electric stirrer (Eurocol no. 855), to a smooth and homogeneous mixture.
• Wait for approx. 3 minutes and stir the mortar once again with a low rpm.
• Apply the mortar within 20 minutes on the floor with a trowel or notched squeegee.
• When pumping, adjust the mixing-device in such way that per 23 kg 990 Europlan Direct 5,5 - 6 litres of cool and clean tap water will be added.
• Protect fresh levelling compound layers against draft and direct sunlight.
• Under normal circumstances the applied layer is passable after 2-3 hours. At a layer thickness of 5 mm the levelling compound layer is ready for the installation of a floor covering after 24 hours.
• For extended information about the safety precautions we refer to the safety data sheet on our website www.eurocol.nl.

Working conditions:
Required surrounding temperature : 18 - 23 °C.
Temperature for material and subfloor : min. 15° - max. 20 °C.
Relative humidity : 40 - 70%.

Underfloor heating systems:
990 Europlan Direct can be applied on underfloor heating systems. The startprotocol of the floorheating needs to be completly executed in accordance with the directives of the supplier. Turn off the heater 24 hours before application; do not heat again until at least 24 hours after installation, in steps of maximum 5 °C water temperature per day.