• Very low emission
• Emicode EC 1PLUS
• Pumpable
• Dust reduced
• Low-tension
• Self-levelling
• Applicable in thicker layers
• High compression strength  

For applying levelling compound layers (3 - 50 mm) with a pump, on cement-based and other stony subfloors which are to be covered with a floor covering.

If applying by pump:

Consult pump supplier, ensure the pump is suitable for all types of levelling compounds. Pumping with too high mixing rate can cause an insufficient flow of the levelling compound. 

Approx. 1.6 kg/m² per mm layer thickness.

• 970 Europlan Nivolux can be applied on any type of stony subfloor that is rigid and has a good tensile and compression strength. The subfloor should also be clean, permanently dry and free from grease and dirt, according to the requirements of BS 8203 or DIN 18 365.
• Decrease smooth and impervious subfloors (tile floors, granito, terrazzo etc.) with 014 Euroclean and dry well afterwards. As well as sandpapered and old (water-resistant) adhesive residues prime with 044 Europrimer Multi with a foam roller.
• Prime porous cement screeds with 044 Europrimer Multi or 049 Europrimer ABS with a foam roller.
• Fill cracks and deep damages with 905 Europlan Fill or 945 Europlan Solid. After hardening prime 905 Europlan Fill or 945 Europlan Solid with 044 Europrimer Multi or 049 Europrimer ABS.
• Fix cracks/seams in the subfloor with 021 Euroblock Reno in combination with 063 Eurotape and 846 Quartzsand or with 808 Eurojoint Connector in combination with 021 Euroblock Reno.
• With asphalt floors and bituminous substrates it is recomanded to ask for technical advice.
• For levelling anhydrite floors use 925 Europlan Alphy Direct or 920 Europlan Alphy.
• In advance always seek our technical data sheets. In doubt about the application ask for technical advice.
  

• In advance consult your pump supplier if the pump is suitable for all types of levelling compounds.
• Make sure there is sufficient supply of 970 Europlan Nivolux in the mixing-device; keep the funnel full.
• Adjust the mixing-device in such way that per 23 kg 970 Europlan Nivolux 5 - 5.5 litres of cool and clean tap water will be added. Take care that the mortar is not floating over the floor.
• By moving the hose steadily and equally over the floor, it is only necessary to determine the thickness of the layer with a divider.
• When applying by hand, add 23 kg of 970 Europlan Nivolux to 5 - 5.5 litres of cool and clean tap water.
• Stir thoroughly, by using an electric stirrer, to a smooth and homogenous mixture.
• After stirring wait for approx. 5 minutes and stir the mortar once again with a low rpm.
• Apply the mortar within 30 minutes on the floor with a trowel.
• Protect fresh levelling compound layers against draft and direct sunlight.
• Under normal circumstances the applied layer is passable after 3-4 hours and in a layer thickness of 3 mm ready for installation after 24 hours.
• In case of layers thicker than 2 mm, it is recommended to measure the residual moisture percentage according to the noted testing method (CM-hydrometer residual moisture < 3 CM%).
• For extended information about the safety precautions we refer to the safety data sheet on our website www.eurocol.nl.

Working conditions:
Required surrounding temperature : 18° - 23° C.
Temperature for material and subfloor : min. 15° - max. 20º C.
Relative humidity : 40-70%.

Underfloor heating systems:
970 Europlan Nivolux can be applied on underfloor heating systems. The startprotocol of the floorheating needs to be completly executed in accordance with the directives of the supplier. Turn off the heater 24 hours before application; do not heat again until at least 24 hours after application and in steps of maximum 5 °C water temperature per day.