SelectYourLanguage

Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2

eurocol
042 EUROBLOCK TURBO

042

One-component damp proof - DPM - and surface reinforcement coating. Fast damp proofing up to 5 CM %, 98% RF. One component. PU-based.

alt-de_042.jpg
  • pdf-product-specification.pdf

    pdf-product-specification.pdf

  • pz_042-turbo_licence_ec1plus_2022_uk.pdf

    pz_042-turbo_licence_ec1plus_2022_uk.pdf

  • safety data sheet_eurocol_042_euroblock_turbo_uk.pdf

    safety data sheet_eurocol_042_euroblock_turbo_uk.pdf

Product Typification



Basis : PU-pre polymer
Colour : Brown.
Consistency : Liquid.

Product advantages:
  • Ready to use, one-component, fast drying, damp proof coating to block residual moisture of absorbent, cement-based subfloors (screed) up to 5 CM %, 98% RF.
  • Very good penetrating properties.
  • Ideal to reinforce surfaces of absorbent cement- and calcium sulphate- (gypsum) based subfloors, before levelling or adhesion works.
  • For subsequent levelling works quartz sand blinding with 846 Europlan Sand is needed of still wet coat.
  • Direct installation of multilayer parquet is possible with approved Eurocol parquet adhesive. Suitable for underfloor heating systems.
  • For indoor use only.
  • Very low VOC emission. Solvent-free. EMICODE EC 1 Plus.
  • Declared by baubook, "ecological building product".

Performances

Consumption : 100 – 150 g/m², for absorbant floors 
Flammability : Non-flammable.
Frost resistance : No.
Special quality : Damp proof membrane up to 5 CM%, 98 % RF..

Application

Application:
  • for blocking non-pressing residual moisture in cement screeds up to 5 CM %, 98% KRL (TKB),
  • for the consolidation of surface edge zones of mineral substrates.

Working Process

Tools : Foam roller or lambswool roller.
Waiting time : 2-24 hours.
Storage : Store cool and free from frost.
Shelf Life : Approx 9 Months, in unopened packaging. After use close the open packaging well.
Drying : Approx 120 - 240 minutes (sticky free surface). *
Cleaner : Spirit.
Frost-proof : No.
Remarks : 

Relevant norms and regulations of the branch are to be respected. Outside Germany relevant national regulations are to be applied which must be known by the user.
Foam building is to be removed by sanding;the area is to be recoated especially when being used as a DPM.
When using as a moisture barrier, make sure there is enough ventilation at skirting and behind cupboards.
Please pay attention to the technical information of the other relevant products and auxiliary material.
No building sanction according to DIN 18195.
Do not use on concrete and dense substrate.

EMICODE, more informations under www.eurocol.com.


* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

Consumption:
100 – 150 g/m², for absorbant floors 

Substrate:
  • The substrate must be pressure- and tension-resistant, free of cracks and dust, even and free of layers that reduce adhesion.
  • Adhesion-reducing layers, old material residues must be removed by suitable mechanical measures in accordance with the specifications of DIN 18365/DIN 18356.
  • Cracks or joints (except structural expansion joints) are to be closed with Eurocol Sealing Compounds Europlan 913 Silicate.
  • On highly structured substrates (milled floors), the primer may run together in the milled traces, which may be associated with material-specific foaming. For these substrates, alternatively use a Eurocol 2-K EP primer approved for this purpose.
  • In case of defects, concerns must be reported in writing.


User manual:

Before use, temper the product according to the processing conditions.

  • Roll out the primer onto the prepared substrate thinly and evenly, avoid puddle formation at all costs, as in thicker layers the hardening is delayed (skin formation) and this can lead to incorrect adhesion, imperfections in the waterproofing.
  • When working with a rubber slider, roll immediately with a short pile lambskin roller (e.g. 4 mm Floor - Oil-Wax Roller) to level and uniform the material application.
  • Intermediate drying times are approx. 120 - 240 minutes depending on the room climate. Low air humidity delays the drying of the primer.
  • Before further processing, the surface must be tack-free.
    If the surface is tack-free or within to 24 hours, it can be bonded directly with Eurocol 1-component and 2-component adhesives.
  • To barrier off residual moisture on cement based substrates, apply a second coat within 24 hours in the same way, thinly and evenly, in cross-coats and also allow to set tack-free until the next processing step.
  • For subsequent levelling work up to 5 mm thick, apply an intermediate coat of 070 Europrimer Fill as an adhesion promoter within 24 hours.
    In case of heavy use of the surface (rolling) and / or high layer thickness of the levelling compound (>5 mm), sprinkle the last layer of the primer with 846 Europlan Sand in excess (1.5-2.5 kg/m²).

Working conditions: 

at least 15 °C floor temperature, 
at least 18°C material and room temperature,
35-75% relative humidity, recommended <65%.





Quality and guarantee

Environment and health

GISCODE : RU1
LEED : VOC 0 g/l, meets: IEQ Credit 4.1
DGNB : VOC 0 %, quality level: 4
Hazard Class : Product contains hazardous ingredients. Please observe the notes in the Safety data sheet!
Safety and environment : Safety data sheets of Forbo Eurocol products according to EEG-guideline 91/155. Keep out of reach of children. Do not eat, drink or smoke while processing the product. Only give completely empty containers for recycling. Bound material residues can be disposed of as household waste. From 24.8.2023, training is mandatory for handling preparations containing isocyanates. https://isopa-aisbl.idloom.events/049-de
MSDS : For extensive information about safety and environment we refer to our website www.forbo-eurocol.de.
Substances causing allergy : Contains isocyanates. May produce an allergic reaction.


Articles

articelproductnamepackagingshipping unit
042Euroblock TurboPE jerry can à 11 kg80/pallet